Unique nylon sleeve that "frizzes" into a self-renewing shield that is extremely resistant to severe abrasion. Also protects operator. Down time and maintenance cost are reduced.
Application:
Maximum protection for an individual hose or group of hoses against physical abrasion and deterioration. Provides burst and containment protection. Meets ISO 6945 abrasion standards.
Features:
These nylon sleeves are unique because they form an extra protective layer against abrasive forces. Specifically, thousands of tiny nylon filaments, woven into the texturized yarn, "friz' into a self-renewing shield that is extremely resistant to severe abrasion. Also resists mildew and bacteria growth.
Material:
Made of tiny nylon filaments
B at the end of the order number denotes that it is brass.
Features:
Provides metered flow in one direction & free-flow in the reverse direction.
•
Lock nut included to secure flow setting.
•
Soft-seat piston check for leak-free service.
•
Ball check option available for high cycle applications.
•
Rugged, all-metal construction - no plastic parts.
•
Maximum operating pressure - 2000 psi for brass.
Brand: Super Swivels
Features:
Available in sizes from 1/4" through 2"
•
Withstands heavy side loads
•
Superior quality alloy steel
•
Chrome ball bearings for long life
•
No snap ring to blow off
•
Burnished (micro smooth) barrel bores
•
Through hardened (not just case hardened)
Brand: Super Swivels
Features:
Available in sizes from 1/4" through 2"
•
Withstands heavy side loads
•
Superior quality alloy steel
•
Chrome ball bearings for long life
•
No snap ring to blow off
•
Burnished (micro smooth) barrel bores
•
Through hardened (not just case hardened)
Brand: Gates
Works off standard shop air (90 PSI). Economical, convenient and versatile for use wherever 90 PSI compressed air is available.
Pressure Rating:
10,000 psi
Brand: Gates
The Gates Power Crimp 707 is the most precise, yet simplest crimper made. It was the first crimper with electronic digital readout to indicate gauge setting. The toughest part about using the 707 is pushing a button. It takes just a few seconds to make factory-quality hose assemblies. Crimps hydraulic hoses from low pressure return lines to extremely high pressure spirals, from 3/16" to 1 1/4" I.D. Crimps straight and bent tube stems, plus 45° and 90° block types.
Dimensions:
13" wide by 12" deep by 26 1/2" high.
Maximum Working Pressure:
4900 psi
Production Rate:
100 assemblies per hour (using 1/2" I.D. two-wire straight thread assemblies).
Brand: Gates
Medium Pressure Hydraulic Power Clean Pressure Washer Hose. 2-Wire Braid Hose. 1-Wire Braid Hose available. See PowerClean™ Pressure Washer Hose - 1-Wire Braid.
Caution:
Use Bend Restrictors to extend service life. Not recommended for steam service.
Coupling Recommendations:
74 MegaCrimp® Couplings.
Cover:
Type C2 (Modified Nitrile). Black. Specially compounded to handle pressure washer environment.
Recommended For:
Heavy duty use on hot and cold water high pressure cleaning equipment where heavy duty service is required. Flexible.
Reinforcement:
High tensile steel two wire braid.
Temperature Range:
-40º C to + 100º C (-40º F to + 212º F). Increased operating temperatures will reduce hose assembly service life.
Tube:
Black. Specially compounded to handle high pressure water service.
Brand: Prince
The Prince valve model RV is a differential poppet type inlet relief. The valve is made up of a relief cartridge and a cast iron valve body. The differential poppet type relief provides smooth quiet performance with a minimum variation between cracking and full flow pressures. This type relief is also less sensitive to system contamination. The model RV is well suited as a system relief up to 30 GPM and 3000 PSI. It is available in two pressure ranges and both an externally adjustable and shim adjustable version.
Capacity:
30 GPM max inlet flow
Maximum Operating Pressure:
3000 PSI
Brand: Prince
Style: SAE "B" Flange Pump - 2 Bolt Mount
The SP25A pump now utilizes self-lubricating thrust blocks that eliminate the need for seperate wear plates. They are made from a high strength aluminum alloy with exceptional anti-galling properties. This new thrust block design also incorporates advanced bearings designed specifically for high pressure hydraulic pumps. This new bearing features a robust fluropolymer PTFE wear surface that yields unsurpassed load carrying capabilites and cavitations resistance even at low speeds and moderate levels of contamination. Also, since the PTFE resin layer is self-lubricating, contamination from bearing wear in high load situations (when no oil film is present) is reduced. This new thrust block design combined with these advanced bearing results in lower friction and less internal oil loss resulting in higher pump efficiencies.
Features:
Patented Non-Symmetrical Gears - the adoption of non-symmetrical gears insures greater power per unit volume compared with pumps of conventional design. The compact gear compartment has enabled high-pressure operation. The increased number of gear teeth has reduced the flow pulsation and minimized the noise.
•
Bearings - PTFE composite bearings are used due to the ability to handle heavy loads, low shaft speeds, and high levels of contamination.
•
Gears and Drive Shaft - Made of hardened alloy steel of one piece construction.
•
Special Gear Design - Non-symmetrical gear insures low noise and compactness.
•
Highest Quality Workmanship - Proudly made in the USA!
•
Pressures up to 3000 PSI.
•
Dependable Service - Balanced pressure loading insures small dispersion, good durability and maintains high performance.
•
Perfect Alignment - "Through bore" design provides perfect alignment of pump element and assures even bearing load.
•
With the aluminum alloy casing, the SP Series features light weight and easy handling.
•
Working oil - a mineral based oil with additives to resist corrosion, oxidation, and foaming is recommended. Viscosity at any running condition should be 60 SUS minimum and 250 SUS maximum. 180°F is the maximum recommended system operating temperature.
•
Per ISO cleanliness code level 17/14. As a minimum, 10 micron filtration is recommended.
Brand: Prince
Features:
- Pressure release detent at end of retract stroke/detent in spool in position
- Relief set to 2,250 PSI
- Max tank port pressure 500 PSI
- Max operating temperature 180°F
Brand: Permco
We carry the following Permco Series Numbers for Sleeve Bushing Pumps: P124, P197, P257, and P360. Click on the 'details' button to see a list of specifications for each series.
Features:
Steel tank assembly with diamond plate top section, fully baffled, two 2" NPT bottom ports, internally diffused, dual mounting rails (2"x2") welded tank assembly
•
Tank is powder coated black
•
Filtered mushroom vent in tank top for increased air exchange
•
Filler/breather assembly-including -40 micron filter/breather cap (chain mounted) with nylon strainer basket and bayonet closure
•
Includes ASK200 mounting and spring kit: four pre-drilled powder coated mounting angles, platted bolts, washers, lock-nuts, four plated springs and four pre-drilled mounting pads
•
Oil level and temperature sight gauge
Features:
Total aluminum construction, top tank section built of Bright Diamond plate, balance bright mill finish, fully baffled.
•
Two heavy duty machined 2" NPT bottom ports, internally diffused
•
Filtered mushroom vent in tank top for increased air exchange
•
Filler/breather assembly-including -40 micron filter/breather cap (chain mounted) with nylon strainer basket and bayonet closure
•
Dual mounting rails (2"x2") welded to tank assembly
•
Mounting kit includes four pre-drilled powder coated mounting angles, plated bolts, washers, lock-nuts, four plated springs, and four pre-drilled mounting pads
•
Oil level and temperature sight gauge
Brand: Bezares
The 3000 Series PTO is designed for the Allison AT/MT/HT model transmissions. This PTO has a low profile housing for easier mounting and is available with various outputs, ratios as well as either electric over hydraulic or air shift options.
Brand: Permco
We carry the following Permco series numbers for Dump Pumps: DM, DMD, DMR, and DG.
THE ONLY DUMP PUMP MADE IN THE USA!
Brand: Super Swivels
Features:
Available in sizes from 1/4" through 2"
•
Withstands heavy side loads
•
Superior quality alloy steel
•
Chrome ball bearing for long life
•
No snap ring to blow off
•
Burnished (micro smooth) barrel bores
•
Through hardened (not just case hardened)