The 1000 and 2000 Series PTO's have been engineered to work with the most common transmissions in today's market. Offered in a wide range of input gear, ratio, output, and shifter options, these cast iron PTO's include large 12mm flange bolts, which make for a very sturdy and durable pump mount, supporting some of the larger pumps in the market.  Both of these models are also available in a deep mount 1010 and i2010 series.  All Bezares PTO's are built with the highest quality bearings and sealing components available.

Brass

Economically designed for effective control of hydraulic and pneumatic actuators where frequent adjustment is not required.

In-Line Filter - Medium Pressure

Features:

• Pressures up to 350 PSI (24 Bar)
• Flows to 75 GPM (284 LPM)
• Suction and Return Line Models
• Cellulose and Wire Mesh Media

The latest in high-tech crimping.  Portable (mobile) crimper is light, versatile and powerful enough to crimp up to 1 1/4" four-spiral hose.  Digital accuracy for precise, consistent crimping.  Crimps low-pressure return line to high-pressure four-spiral 1/4" I.D. (-4) through 1 1/4" (-20) hose right on the job site.  Bottom loading feature provides clear view of crimping area.  Unique die design holds coupling in crimping position to free hands.  Light comes on and a buzzer sounds when crimp is complete.  Portable (57 lbs) or can be mounted permanently on service vehicle or work bench.

No power source needed.  Convenient and portable for use anywhere. Make OEM factory-type assemblies, on the spot, to minimize down time.

The Prince RD-1800 Valve is a direct acting ball/spring type pressure relief. The valve is compact and simple in design. This type relief is fast opening and is well suited for pressure spike protection. The performance curves below indicate the low cracking pressure typical to ball/spring reliefs. The valve has a standard steel seat, externally adjustable.

For G2, G2H, J2AT, G1, G1H, C5C, C5E, C5R and G4H Hoses and Power Crimp Stems.

A series  of spin-on filter elements are accessorized with a selection of filter heads for a variety of applications.  Indicators, gage ports and by-pass valves are available to customize each application.

Hydraulic fluids are efficiently filtered through return line applications.  Maximum working pressure 100 PSI/Burst 300 PSI.

Used for:

·Off Highway    ·Ground Transportation      ·Mobile Equipment      ·Industrial in-plant equipment      ·Marine hydraulic systems

Medium Pressure Hydraulic Power Clean Pressure Washer Hose.  1-Wire Braid Hose.  2-Wire Braid Hose available.  See PowerClean™ Pressure Washer Hose - 2-Wire Braid.

STANDARD FEATURES:

• Handle can be installed in "up" or "down" position
• Detent release pressure adjustable from 1000 to 2000 PSI
• Relief valve adjustable up to 2750 PSI
• Pressure release detent spring center to neutral is 1200 PSI
• Not convertible from open center to closed center

The SP20B pump now utilizes self-lubricating thrust blocks that eliminate the need for seperate wear plates.  They are made from a high strength aluminum alloy with exceptional anti-galling properties.  This new thrust block design also incorporates advanced bearings designed specifically for high pressure hydraulic pumps.  This new bearing features a robust fluoropolymer PTFE wear surface that yields unsurpassed load carrying capabilities and cavitation resistance even at low speeds and moderate levels of contamination.  Also, since the PTFE resin layer is self-lubricating, contamination from bearing wear in high load situations (when no oil film is present) is reduced.  This new thrust block design combined with these advanced bearing results in lower friction and less internal oil loss resulting in higher pump efficiencies.

5" & 10" slotted for side viewing

Spiral wrap, used as a guard on single hoses or to bundle hoses, is the proven way to protect hose, wire, cable, etc., against chaffing, rubbing, crushing, ultraviolet, and other enviromental hazards that causes premature failure.  Users have realized a dramatic increase in serviceable life and reduction in costly repairs and down time.  SAVES MONEY!

The Versa-pak Flow Control/Unloader unit is ideal for most residential and commercial refuse hydraulic systems.  Applications include residential and commercial front loaders, rear loaders, automated side loaders, compactors, roll-offs, recycle and all PTO driven pump applications.

The Flow Control/Unloader configuration has both the Flow Control and Unloader function.  By flipping a switch on the dash, the operator can go in to the Unload mode where full flow is diverted back to the tank at low pressure.  This function reduces system heat buildup and horsepower losses resulting in substantial vehical fuel efficiencies.

The WR Series motor incorporates the latest advances for smooth performance, efficiency and durability.  It features an optimized Roller Stator® geometry with seven precision rollers to eliminate sliding friction and provide rolling contact between the rotor and stator.  This increases motor efficiency.  A three-zone spool valve, integral check valves and a provision for a case drain reduce pressure on internal seals to improve product life.  A wide variety of mounting, shaft, motor displacement and porting options are available to meet all application needs.

Ideally suited for power units, mobile equipment, machine tools and test equipment.  Side mount capability.  Excellent alternative to spin-ons when space is at a premium.

Features:

·Cast aluminum head

·Steel bowl

·Optional 2nd inlet port

·Variety of port sizes

·Elements interchange with Shroeder "K" Series

·Indicator ports available

·Options:  magnet, check valve, and mounting kits

The 1000 and 2000 Series PTO's have been engineered to work with the most common transmissions in today's market. Offered in a wide range of input gear, ratio, output and shifter options, these all cast iron PTO's include large 12mm flange bolts, which make for a very study and durable pump mount, supporting some of the larger pumps in the market.  Both of these models are also available in a deep mount 1010 and i2010 series.  All Bezares PTO's are built with the highest quality bearings and sealing component available.